+91 70057 36620ilustraca.edu@gmail.com

ILU-800-SH02 Gantry Girder Design (IS 800:2026)

Designs a crane runway girder made of a rolled I-section with an optional channel cap, from the crane supplier’s data.

Use it for Crane gantries in workshops, factories and warehouses with EOT or hand-operated overhead cranes
Sections Any I-section from the database, with an IS 808 channel cap (ISMC 150 to ISMC 400) or none
Crane loads it works out Maximum wheel load with the crab at minimum hook approach; vertical impact (+25 % EOT, +10 % hand); lateral surge (10 % / 5 % of crab + lifted load); worst wheel positions for moment and shear
Checks (IS 800:2026) Compound section properties · Annex E elastic critical moment for monosymmetric sections with wheel load above the shear centre and Table 40 factors · lateral torsional buckling, 15.2.2 with Table 13 · bottom flange bending · biaxial bending of the top flange (vertical + surge) · shear, 15.4 · web bearing under the wheel, 15.7.4 · web buckling under the wheel, 15.7.3.1 · vertical deflection span/500, /750 or /1000 and lateral deflection span/400, Table 6
You enter I-section and cap channel; crane type; capacity, crab weight, bridge weight, crane span, hook approach, wheel base; gantry span, rail weight and height; LTB length factor; moment diagram for Table 40
You get Wheel loads with and without impact, surge, factored moments and shear, compound Iz, Iy, Ztop, Zbottom, Mcr, χLT, all design strengths, deflections, the governing check, ADEQUATE / NOT ADEQUATE
Not covered Tandem cranes and more than two wheels per end carriage; longitudinal braking force; fatigue (Section 18); torsion from rail eccentricity; bumper loads; welded plate girders; continuous gantries

Know before buying: Pack C covers hot-rolled purlins and gantry girders. Cold-formed Z / C purlins, roof trusses, portal frames and columns are not in this pack. Full details: Pack C page.

Common to both workbooks

  • Design code: IS 800:2026 (Fourth Revision), limit state method; γm0 = 1.10. Load combinations from Table 4; loads to IS 875 (Part 2) and inputs from IS 875 (Part 3).
  • Software: Microsoft Excel 2016 or later on Windows or Mac, including Microsoft 365. No macros, add-ins or internet connection needed.
  • Not supported: Google Sheets, LibreOffice, Excel Online editing.
  • Units: kN, kNm, m for loads and lengths; mm for dimensions; kN/m² for area loads; MPa for stresses.
  • Steel grades: IS 2062 E250 to E450 (fy reduces with thickness), EN S275 / S355 / S460, IS 4923 / IS 1161 YSt grades for hollow purlins.
  • Section database: 3,525 sections: IS 808:2021, SAIL, Jindal, Tata Structura, APL Apollo, ArcelorMittal, British Steel, IS 4923 / IS 1161.
  • Key drawing: the Input tab carries a labelled drawing that shows what every input means (roof section and plan for purlins; girder section, wheels and crane plan for gantries).
  • Tabs: Guide, Input (inputs, live results, key drawing), Summary (one-page report), Detailed (clause-by-clause calculation), Project (report title block).
  • Reports: A4 portrait, print or save as PDF. Every page carries your company name, project, client, job no., calc no., revision, date, made / checked / approved by and issue status (Preliminary to GFC). Your logo can be added to the report header.
  • Protection: all formulas are locked; only the shaded input cells can be edited.
  • Support: Ilustraca Academy, ilustraca.tech@gmail.com

Engineer’s responsibility: these workbooks are design aids. Results must be reviewed by a qualified structural engineer, who remains responsible for the design. Wind pressure and pressure coefficients are entered by you from IS 875 (Part 3); crane data comes from the crane supplier.

Share this article
Picture of Er. Sandip Deb

Er. Sandip Deb

Founder of Ilustraca Academy and a practising structural engineer in Kolkata. B.Tech (Civil), AMIE, CEng(I), Empanelled Structural Engineer with NKDA & KMC. He teaches RCC and steel design the way design offices work, with every software result checked by hand against the IS codes.

Learn it properly, step by step

Self-paced courses on ETABS, STAAD.Pro, RCDC and IS codes, plus hundreds of free lectures.

error: Content is protected !!
Scroll to Top