+91 70057 36620ilustraca.edu@gmail.com
IS 800:2026 · INDUSTRIAL SHEDS

Pack C: Industrial Shed Pack (IS 800:2026)

Design purlins and crane gantry girders to the new IS 800:2026, with loads, combinations and clause-referenced reports done for you.

₹500 both workbooks · or ₹299 each

After payment you download the .xlsx files instantly, and the download link is also emailed to you. If you do not see the email within a few minutes, check your Spam or Promotions folder and mark it “Not spam”.

What’s inside

ILU-800-SH01Roof Purlin Design

Works out purlin loads from the roof geometry and designs the purlin for biaxial bending under all Table 4 combinations, including wind uplift.

Use it for & key clauses

Use it for: Roof purlins of industrial sheds, warehouses, workshops, canopies; checking existing purlins

Key clauses: Classification, Table 2 · bending about both axes to 15.2.1 with the elastic-modulus cap · lateral torsional buckling under uplift (bottom flange in compression), 15.2.2 · biaxial bending as required by 15.9 and Section 16 · shear, 15.4 · deflection span/150 elastic or span/180 brittle cladding, Table 6

₹299Buy SH01
Full specs →
ILU-800-SH02Gantry Girder Design

Designs a crane runway girder made of a rolled I-section with an optional channel cap, from the crane supplier’s data.

Use it for & key clauses

Use it for: Crane gantries in workshops, factories and warehouses with EOT or hand-operated overhead cranes

Key clauses: Compound section properties · Annex E elastic critical moment for monosymmetric sections with wheel load above the shear centre and Table 40 factors · lateral torsional buckling, 15.2.2 with Table 13 · bottom flange bending · biaxial bending of the top flange (vertical + surge) · shear, 15.4 · web bearing under the wheel, 15.7.4 · web buckling under the wheel, 15.7.3.1 · vertical deflection span/500, /750 or /1000 and lateral deflection span/400, Table 6

₹299Buy SH02
Full specs →

Less input, more output

SH01 Roof Purlin works out: roof imposed load from the slope (IS 875 Part 2), the split into normal and down-slope parts, all five Table 4 combinations, and LTB under wind uplift with the bottom flange in compression.
SH02 Gantry Girder works out: wheel loads with impact (+25 % EOT, +10 % hand), lateral surge, the worst wheel positions for moment and shear, compound section properties and the Annex E Mcr for the monosymmetric section.

Know the arrangement

Each Input tab carries a labelled key drawing that shows what every input means: the roof section and plan for purlins, and the girder section, wheels and crane plan for gantries.

Which one should I buy?

If you mostly designBuy
Roofs of sheds and warehousesSH01
Workshops and factories with overhead cranesSH02
Complete industrial shedsFull Pack C
Complete steel buildings with connectionsPack A + Pack B + Pack C

All workbooks share the same Project tab, report title block and format as Packs A and B. Each workbook is self-contained and works without the others.

Before you buy

Requirements: Microsoft Excel 2016 or later on Windows or Mac, including Microsoft 365. Not for Google Sheets, LibreOffice or Excel Online editing.

What is not covered:
  • ILU-800-SH01: Cold-formed Z / C purlins (IS 801 / IS 811); LTB of the bottom flange in hogging zones of continuous purlins under gravity; design of sag rods and cleats; calculation of wind pressure
  • ILU-800-SH02: Tandem cranes and more than two wheels per end carriage; longitudinal braking force; fatigue (Section 18); torsion from rail eccentricity; bumper loads; welded plate girders; continuous gantries
  • Roof trusses, portal frames and columns are not in this pack.

Your inputs: wind pressure and pressure coefficients are entered by you from IS 875 (Part 3); crane data comes from the crane supplier.

Engineer’s responsibility: these workbooks are design aids. Results must be reviewed by a qualified structural engineer, who remains responsible for the design.

Frequently asked questions

Do I need macros?

No. The workbooks open in Microsoft Excel 2016 or later with no macros, add-ins or internet connection.

Can I put my company logo?

Yes. Reports carry only your office details. Add your logo once to the report header (Page Layout › Print Titles › Header/Footer › Custom Header › Insert Picture).

Is it IS 800:2026 or 2007?

IS 800:2026 (Fourth Revision), limit state method, γm0 = 1.10, with load combinations from Table 4.

Does it design cold-formed Z purlins?

No. SH01 designs hot-rolled purlins (channels, I-sections, SHS, RHS). Cold-formed Z / C purlins to IS 801 / IS 811 are not covered.

Where do the crane data come from?

From the crane supplier: capacity, crab weight, bridge weight, crane span, hook approach and wheel base. SH02 works out the wheel loads, impact and surge from them.

Does it check fatigue?

Not in Pack C. Fatigue (Section 18), longitudinal braking force, torsion from rail eccentricity and bumper loads are not covered. For fatigue, use the separate ILU-800-FT01 Fatigue Design and Check workbook.

Is it one computer or the whole office?

Each purchase is a personal, non-transferable licence for your own work. See the Terms and Conditions.

How do I receive the files and get support?

You can download the files right after payment, and the download link is emailed to you. If you do not see the email within a few minutes, check your Spam or Promotions folder and mark it “Not spam”. For support, write to ilustraca.tech@gmail.com.

Designing a complete industrial shed?

Pack A designs the members, Pack B the bolts and welds, and Pack C the purlins and gantry girders. Same title block, same report format.

Questions? Email ilustraca.tech@gmail.com

Talk to us

Questions about a course, a StructDesk licence, or inviting Er. Sandip Deb for a lecture or workshop? Get in touch.

Phone / WhatsApp+91 70057 36620
Emaililustraca.edu@gmail.com
Message on WhatsApp
error: Content is protected !!
Scroll to Top