+91 70057 36620ilustraca.edu@gmail.com

ILU-800-FT01 Fatigue Design and Check (IS 800:2026)

Constant and variable amplitude fatigue of members, welds and bolts to IS 800:2026 Section 19: Table 26 detail categories, Table 25 safety factors, thickness correction, cumulative damage, exemption check and fatigue life.

Use it for Crane gantry girders, crane runway details, members, welds and bolts under repeated loading
Checks (IS 800:2026 Section 19) 19.1 scope · 19.2.1.1 thickness correction μr · 19.2.1.2 when fatigue assessment is needed and the exemption conditions with ffeq · 19.2.2.1 Table 24 multiplying factors (entered) · 19.2.3 partial safety factors, γff = 1.0 and Table 25 γmft · 19.3 / Table 26 (A) to (D) detail categories · 19.4 S-N curves (slope 3 up to 5 × 10⁶, slope 5 to 10⁸) · 19.5.1 design strength · 19.5.2.1 / 19.5.2.2 stress limits · 19.5.2.3 / 19.5.2.4 constant and variable amplitude (cumulative damage) assessment
You enter Detail ID; Table 26 detail category for normal stress and for shear; consequence of failure and inspection (γmft); thickness correction for transverse welds joining plates thicker than 25 mm; Table 24 factor; steel grade and thickness; maximum service normal and shear stress; design life and working days per year; up to six load blocks of stress range and cycles per day
You get Total cycles NSC, γmft, μr, design fatigue strength ffd, equivalent range ffeq, exemption check, cumulative damage Df and Dτ, stress-limit checks, fatigue life in years, governing utilisation ratio, ADEQUATE / NOT ADEQUATE, and a live S-N chart with your load blocks plotted
Not covered Stress ranges are entered, not calculated (derive them from your analysis at the detail); rain-flow counting of irregular histories; interaction of normal and shear stress at the same point; corrosion, low-cycle and thermal fatigue; temperatures above 150 °C

Good with Pack C: SH02 Gantry Girder Design does not check fatigue; FT01 does. For a gantry girder, one crane pass is one cycle and Δf = (Mmax − Mmin)/Z at the detail. See Pack C.

About the workbook

  • Software: Microsoft Excel 2016 or later on Windows or Mac, including Microsoft 365. No macros, add-ins or internet connection needed.
  • Tabs: Guide, Input (inputs, live results, live S-N chart, detail-category help), Summary (one-page report), Detailed (clause-by-clause calculation), Project (report title block).
  • Reports: A4, print or save as PDF. Every page carries your company, project, client, document no., revision, date, designed / checked / approved by and issue status. Your logo can be added to the report header.
  • Protection: yellow input cells only; everything else is calculated and locked.
  • Same format as Packs A, B and C, with the same Project tab and title block.
  • Support: Ilustraca Academy, ilustraca.tech@gmail.com

Engineer’s responsibility: this workbook is a design aid. Results must be reviewed by a qualified structural engineer, who remains responsible for the design.

Share this article
Picture of Er. Sandip Deb

Er. Sandip Deb

Founder of Ilustraca Academy and a practising structural engineer in Kolkata. B.Tech (Civil), AMIE, CEng(I), Empanelled Structural Engineer with NKDA & KMC. He teaches RCC and steel design the way design offices work, with every software result checked by hand against the IS codes.

Learn it properly, step by step

Self-paced courses on ETABS, STAAD.Pro, RCDC and IS codes, plus hundreds of free lectures.

error: Content is protected !!
Scroll to Top