+91 70057 36620ilustraca.edu@gmail.com
IS 800:2026 · FOURTH REVISION

Pack A: Steel Member Pack (IS 800:2026)

Design steel members to the new IS 800:2026 in minutes. Clause-referenced reports ready for submission.

₹1,199 all 5 workbooks · or ₹299 each

After payment you download the .xlsx files instantly, and the download link is also emailed to you. If you do not see the email within a few minutes, check your Spam or Promotions folder and mark it “Not spam”.

What’s inside

ILU-800-S01Cross-Section Capacity

Design strengths of a cross-section with no member buckling: tension, compression (squash), bending about both axes, shear and the combined N + M section check.

Use it for & key clauses

Use it for: Quick capacity of a section, fully restrained members, short stocky members, checking section strength at a joint, comparing sections

Key clauses: Classification, Table 2 (2026 limits, including web limits under axial force) · effective area of slender sections, 10.8.2(d) · tension, 13.2 / 13.3 · compression of the cross-section, 14.1.2 / 14.3.2 · bending about z-z and y-y, 15.2.1 with the 1.2 / 1.5 Ze cap · shear including web shear buckling, 15.4 · high-shear reduction, 16.2 · combined axial force and bending, 16.3.1 and Table 17

₹299Buy S01
Full specs →
ILU-800-C01Compression Member Design

Designs axially loaded columns and struts for flexural buckling about both axes, including single angle struts.

Use it for & key clauses

Use it for: Columns, posts, struts, truss compression members, bracing in compression

Key clauses: Buckling classes a0 to d, Tables 7, 8 and 10 · effective length from end conditions, Table 11 (or your own K) · effective area of slender sections, 14.3.2 · single angle struts loaded concentrically or through one leg, 14.5.1 with Table 12 · slenderness limits, Table 3

₹299Buy C01
Full specs →
ILU-800-B01Beam Design — Laterally Unsupported

Designs beams in major-axis bending with the new IS 800:2026 lateral-torsional buckling method, plus shear and deflection.

Use it for & key clauses

Use it for: Floor and roof beams, secondary beams, lintels, cantilevers, purlin-type members without full lateral restraint

Key clauses: Classification, Table 2 · laterally supported strength, 15.2.1 · lateral-torsional buckling with χLT, fm (Table 14) and αLT (Table 13), 15.2.2 · elastic critical moment Mcr, 15.2.2.1 · effective length LLT from Tables 15 and 16 · shear including web shear buckling, 15.4 · high-shear moment reduction, 16.2.2 · deflection limits, Table 6

₹299Buy B01
Full specs →
ILU-800-BC01Beam-Column Design

Designs members carrying axial force with bending about both axes, using the IS 800:2026 member interaction factors.

Use it for & key clauses

Use it for: Frame columns, portal frame members, eccentrically loaded columns, rafters, members straight out of ETABS / STAAD results

Key clauses: Classification under combined N + M, Table 2 · tension, Section 13 · flexural buckling, 14.1.2 · bending about both axes including LTB, 15.2 · shear in both directions, 15.4 · high shear, 16.2 · section interaction, 16.3.1 and Table 17 · tension with bending, 16.3.2.1 · member buckling interaction, 16.3.2.2 with Kzz, Kyy, Kzy, Kyz (Table 18) and Cm (Table 19) · slenderness, Table 3

₹299Buy BC01
Full specs →
ILU-800-T01Tension Member Design

Designs tension members including the end-connection effects IS 800:2026 requires: net-section rupture with shear lag and block shear.

Use it for & key clauses

Use it for: Truss ties, bracing in tension, hangers, sag members, angle and channel ties

Key clauses: Yielding of gross section, 13.2 · rupture of net section, 13.3.1 · shear lag of angles connected through one leg (β), 13.3.3 / 13.3.4 · block shear of bolted ends, 13.4.1 · slenderness, Table 3

₹299Buy T01
Full specs →

Why engineers use it

Live results as you type. Every check updates instantly with SAFE / NOT ADEQUATE.
3,525 sections: IS 808:2021, SAIL, Jindal (JSPL), Tata Structura, APL Apollo, ArcelorMittal, British Steel and IS 4923 / IS 1161.
Reports ready to submit: one-page Summary and clause-by-clause Detailed reports, A4 portrait, print or save as PDF.
Your office on every page: company name, logo, project, client, job no., calc no., revision and issue status (Preliminary to GFC).
No macros, no setup: opens in Excel 2016 or later. Formulas are locked; only the shaded input cells can be edited.
Consistent package: all five workbooks share the same Project tab, title block and format.

Which one should I buy?

Buy the full pack if you design steel structures regularly; buy single workbooks only for a specific member type.

If you mostly designBuy
Columns and strutsC01
Beams, secondary beams, cantileversB01
Frame members from ETABS / STAAD resultsBC01
Truss ties and bracingT01 (with C01 for members that reverse into compression)
Quick section checks of restrained membersS01
Complete steel buildings, sheds, mezzaninesFull Pack A

Every workbook is self-contained: it carries its own section database and works without the others. S01 alone does not check buckling, so do not buy S01 for columns or unrestrained beams.

Before you buy

Requirements: Microsoft Excel 2016 or later on Windows or Mac, including Microsoft 365. Not for Google Sheets, LibreOffice or Excel Online editing (drop-downs and formulas may not behave).

What is not covered:
  • ILU-800-S01: Flexural, torsional and lateral-torsional buckling; member interaction (16.3.2); block shear and shear lag; bending of angles; high-shear reduction for minor-axis bending
  • ILU-800-C01: Torsional and torsional-flexural buckling, 14.1.2.2 (matters for channels, angles and tees); double angles and built-up members; compression with bending (use BC01)
  • ILU-800-B01: Biaxial bending or axial force (use BC01); monosymmetric and welded plate girders; web bearing and buckling under point loads; torsion; deflection of continuous beams (simply supported and cantilever formulae only)
  • ILU-800-BC01: Angles; torsional-flexural buckling of open asymmetric sections, Annex E
  • ILU-800-T01: Staggered holes; threaded rods; block shear of welded ends (13.4.2); strength of the bolts and welds themselves (Pack B)
  • Pack A designs members, not their connections (see Pack B: Bolt & Weld).

Engineer’s responsibility: these workbooks are design aids. Results must be reviewed by a qualified structural engineer, who remains responsible for the design. Section sizes come from each producer’s published ranges; confirm availability with the supplier before specifying.

Frequently asked questions

Do I need macros?

No. The workbooks open in Microsoft Excel 2016 or later with no macros, add-ins or internet connection.

Can I put my company logo?

Yes. Reports carry only your office details. Add your logo once to the report header (Page Layout › Print Titles › Header/Footer › Custom Header › Insert Picture).

Is it IS 800:2026 or 2007?

IS 800:2026 (Fourth Revision), limit state method, with γm0 = 1.10 and γm1 = 1.25 from Table 5.

Which steel sections are included?

3,525 sections from IS 808:2021, SAIL, Jindal (JSPL), Tata Structura, APL Apollo, ArcelorMittal, British Steel and IS 4923 / IS 1161. Each module carries the section types it designs.

Can I check angles and channels?

Yes, within each workbook’s scope: angles in S01, C01 and T01; channels in all five. Torsional-flexural buckling of channels, angles and tees (Annex E), double angles and built-up members are not covered.

How do I get a PDF report?

File › Print › “Microsoft Print to PDF”. Reports are A4 portrait.

Is it one computer or the whole office?

Each purchase is a personal, non-transferable licence for your own work. See the Terms and Conditions.

How do I receive the files and get support?

You can download the files right after payment, and the download link is emailed to you. If you do not see the email within a few minutes, check your Spam or Promotions folder and mark it “Not spam”. For support, write to ilustraca.tech@gmail.com.

Sample reports

Real output from ILU-800-BC01 Beam-Column (NPB 400×180×66.31, E250). Every workbook prints both reports with your office title block.

Summary report · 1 page
Summary report · 1 pageDesign data, every check with clause, demand, capacity and utilisation, and the governing result.View full sample (PDF) ↗
Detailed report · 4 pages
Detailed report · 4 pagesClause-by-clause calculation: section properties, classification, LTB, interaction factors Kzz…Kyz, Cm and final UR.View full sample (PDF) ↗

Talk to us

Questions about a course, a StructDesk licence, or inviting Er. Sandip Deb for a lecture or workshop? Get in touch.

Phone / WhatsApp+91 70057 36620
Emaililustraca.edu@gmail.com
Message on WhatsApp
error: Content is protected !!
Scroll to Top